A thermostat helps in regulating the heating and cooling output of the furnace. To reset a thermostat, find and press the reset button for about 5 seconds or switch off your thermostat for 30 seconds before turning it back on. Replace dead batteries in your thermostat, or turn the battery on and off for 5 seconds while the thermostat is off. Unplug your electrical circuit breaker and leave it for around 30 seconds to cut off power entirely to your home’s HVAC. Clean and reset your thermostat every few months to keep it accurate and working well. You can also get help from a furnace installation service provider for optimum and fast thermostat reset results.
How to Reset a Thermostat? Methods To Follow
It is important to adjust the thermostat settings for optimal results. If these are not correct, reset using the following steps:
Method 1: Press The Reset Button
Hold the reset button for 5 seconds. Most thermostats have a dedicated reset button: it’s sometimes on the edges of the thermostat. You can even remove the thermostat from the wall and observe the back to locate the button. The reset button is often small, so use a paperclip or push-pin to press and hold the button for at least 5 seconds or until the thermostat appears to reset. After you’ve reset your thermostat, set it to your desired temperature and monitor your home’s HVAC system for any changes.
Method 2: Switch Off Your Thermostat
Turn the power switch to the off position or press the power button until the display goes blank. Then, leave the thermostat switched off for 30 to 60 seconds to allow it to be reset and forget the previous settings. Switch on the furnace thermostat again and see if it is working properly.
Method 3: Flip Or Replace The Batteries.
You can replace your thermostat’s battery or flip it and see if the overall thermostat performance improves. Remove the battery from the thermostat and insert it again in an upside-down orientation. Keep it off and let it rest for 5-10 seconds, then insert it again in the position set earlier. It is an effective approach to resetting your thermostat settings to optimize its efficiency. You can use this method for thermostats using a battery power source, like programmable thermostats.
Method 4: Shut Off Your Breaker
Your HVAC system connects to your home’s circuit breaker to ensure a smooth flow of electric current. Switch off the thermostat, and find your breaker box (they are usually present in a utility room or outside at the back of your house). Flip the switch that corresponds with the room in which your thermostat sits or which particularly controls the HVAC. Wait for at least 30 seconds, then restore it. Finally, turn your thermostat back on. You can use this method mostly for digital thermostats.
Method 5: Smart Reset The Thermostat
To reset a smart thermostat, go to the settings menu. You can control the most modern thermostats through their software or an app on your phone. Press the Settings menu on your thermostat, select the option set, and the device will continue with the instructions on the screen to complete the reset process.
Method 6: Call An Electrician Or An HVAC expert
There are different types of thermostats, and resetting one for your house is more complex than flipping a switch. If you need help, it would be better to call a professional and have them fix your home’s cooling and heating systems.
When To Change The Thermostat Setting?
- After A Power Outage: Your thermostat could go out of order after a power outage and not calibrate correctly to the room temperature. Give your thermostat a quick reset to “catch up.” Many thermostats are more sensitive as they boot up and rectify after a reset.
- Out Of Sync: Sometimes, your thermostat can become disconnected from the rest of your home’s appliances and be very slow to adjust to the balance of your heat and cooling system. It may cause your AC or heating to run too long or too little to achieve an optimal effect, requiring a thermostat recalibration.Â
- Regular Service Reset: Like any electronic hardware, your thermostat’s calibration might get disturbed over long periods. To help the calibration process remain accurate and reliable, it’s best to do a reset.
What Are The Signs That Require Troubleshooting For Your Thermostat?
Some specific signs indicate the requirement for thermostat troubleshooting, which are:
- Fluctuating Temperature Levels: According to the thermostat, the room feels hotter or cooler than it is. Resets will clear an inefficient sensor.
- Unresponsive Controls: You have turned up the thermostat, but nothing changes. A reset can get controls performing again.
- HVAC Runs Continuously: The system runs continuously without a set thermostat. A reset can restore proper cycle functioning.
Resetting your thermostat is an easy first step in troubleshooting temperature control issues. If problems persist after a reset, you should contact an HVAC technician for additional diagnostics and repairs.
Conclusion
You can reset the furnace thermostat to restore its functioning and optimum performance. A thermostat requires rest when it is out of calibration or after a power outage. First, use the thermostat button, replace the batteries, turn off the breaker, switch off the thermostat, and turn it on again. You can also ask for help from a furnace installation service provider to get reliable results and improve your home environment.
Click here and read more blogs
